Go Back   4x4 Response UK > National Forums > Come on in

Reply
 
Thread Tools Display Modes
  #1  
Old 16-01-2018
james.chalkley's Avatar
james chalkley james.chalkley is offline
Group Management
Forum Handle: james.chalkley
Kent 4x4 Response
 
Join Date: Jun 2012
Location: Kent
National Callsign: SE140
Posts: 93
Default Training Titbits .. Jumpstarting

The latest instalment from the SE4x4R training team.

And now with added video https://www.youtube.com/watch?v=BJWGCnghf6o

Jump leads are a handy way of recharging a flat battery, but they can cause real damage to both cars and people if they’re not used properly.

Important safety information
Batteries produce flammable gases, so:
never try to jump start a battery that looks damaged or is leaking
don’t use jump leads that are damaged
stop using the jump leads if they get hot. Switch off both engines and allow the leads to cool to avoid a possible fire
never smoke or allow naked flames anywhere near either battery
don’t let any metal objects come in contact with the cars’ batteries, as these could cause a spark and possibly make the battery explode. That includes rings, necklaces, watch straps, hand tools, clips, stray wires etc
Don't remove the jump leads while the cars’ engines are running. This can cause serious damage to the cars’ electronics
Before you start, remove any loose-fitting clothing – like a scarf or tie – as these could get caught up in the moving engine parts
A step-by-step guide
Find someone with a car who’s happy to help. Their car must have a fully charged battery with the same voltage as yours (usually 12 volts)
Park both cars so their batteries are within easy reach of one another (without the cars actually touching). Keep the handbrakes on and the ignitions off
Use the red jump lead to connect the working battery’s positive (+) terminal to the flat battery’s positive (+) terminal
Take the black jump lead and attach it to the negative (-) terminal on the working battery. Then attach the other end to an earthing point (unpainted metal on the engine block or chassis) well away from the flat battery and fuel system
Keep both engines off and wait for three minutes, then start the working car’s engine and let it run for a minute
Start your car
Leave both cars to idle, at a fast pace, for around 10 minutes
Turn off both cars’ engines and carefully disconnect the leads in the reverse order to the way they were connected (i.e. remove the black lead from your car first and finish with the red lead from the other car). Make sure the leads don’t touch one another, or either car, as you remove them
Restart your car
If your car won’t start there’s probably a more serious problem requiring professional help
__________________
Defender 50th Anniversary GB 165
twitter @james_SE140
Vice Chair South East 4x4 Response
Reply With Quote
  #2  
Old 16-01-2018
Jerry G JerryG is offline
Group Membership Admin
Forum Handle: JerryG
Gloucestershire & Worcestershire 4x4 Response
 
Join Date: Feb 2011
Location: Kempsford, Gloucestershire
National Callsign: GW43
Amateur Radio Callsign: M6JJG
Posts: 107
Default Jump Starting

Quote (partial) 'Don't disconnect while engine running. Can seriously damage cars electronics.'
Yet utube video shows just that! Explain.
Reply With Quote
  #3  
Old 06-02-2018
steve.herts's Avatar
Stephen Marquis steve.herts is offline
Website User
Forum Handle: steve.herts
 
Join Date: Jun 2016
Location: Barnet
Posts: 26
Default

Quote:
Originally Posted by JerryG View Post
Quote (partial) 'Don't disconnect while engine running. Can seriously damage cars electronics.'
Yet utube video shows just that! Explain.
If you switch off to disconnect jump leads, there is a pretty good chance the dud vehicle will not restart as it will not have gained enough charge to restart yet.

Both vehicles should also switch off unnecessary electrical loads, heated screens, sidelights only etc during the process,and the dud vehicle should maintain minimum necessary electrical load until it is certain there is enough charge stored to enable restarting

Sent from my VFD 600 using Tapatalk
__________________
Unsuitable for motor vehicles. A challenge not a warning
Reply With Quote
  #4  
Old 08-02-2018
Gordon-Brown's Avatar
Gordon Brown Gordon-Brown is offline
Group Management
Forum Handle: Gordon-Brown
Northants 4x4 Response
 
Join Date: May 2009
Location: St Neots
National Callsign: NH47
Posts: 317
Default

Indeed - the instruction to switch-off to disconnect the leads goes against the training I've had previously, not to mention the instruction for undertaking a jump-start in my vehicle's handbook.

I'd be interested to hear the rationale / provenance of that particular approach.
__________________
Gordon Brown
Northants 4x4 Response Chairman & Trustee
4x4 Response UK


Land Rover Defender & Discovery 4
Reply With Quote
  #5  
Old 08-02-2018
James Addy JamesAddy is offline
Website User
Forum Handle: JamesAddy
 
Join Date: Dec 2012
Location: Staffordshire
Posts: 55
Default

I agree, in that the way I was taught was to start engine and leave running whilst carefully removing the leads.

And my guess is that any 'official' training, may say turn off engines before disconnecting to try and safeguard any shorting or Engine Management Unit issues (But can't see how it would avoid any of that if the engines were off - your dealing with potentially raw electricity, so be careful, be safe, and keep the leads apart at both ends at all times until nowhere near vehicles and/or batteries)

Regards James
Reply With Quote
  #6  
Old 08-02-2018
Jerry G JerryG is offline
Group Membership Admin
Forum Handle: JerryG
Gloucestershire & Worcestershire 4x4 Response
 
Join Date: Feb 2011
Location: Kempsford, Gloucestershire
National Callsign: GW43
Amateur Radio Callsign: M6JJG
Posts: 107
Default

Well you could switch off the donor vehicle to halve the perceived problem. But actually, whether the engines are running or not, you still have live 12+ volts at both ends with no short circuit protection!
So as the previous poster says, keep leads apart and clear of everything.
The donor should start again as it was full up before the jump start.
Put some electrical load on the 'jumped' vehicle to stabilise the voltage, not too much, before disconnecting.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

» Log in
User Name:

Password:

Not a member yet?
Register Now!
» Sponsors

» Donate to 4x4 Response
» Online Users: 100
0 members and 100 guests
No Members online
Most users ever online was 8,564, 03-10-2024 at 07:40 PM.



All times are GMT. The time now is 04:00 AM.
Powered by vBulletin® Copyright ©2000 - 2016, Jelsoft Enterprises Ltd.
All content copyright © 4x4 Response UK. All rights reserved.
Registered Charity 1168451
Design/Hosting: YR 4x4 Response